1. A comparative study on the machinability of Ti-6Al-4V using conventional flood coolant and sustainable dry machining. (2015) Authors: Dawood, Abdulhameed; Arbuckle, Gregory K.; Jahan, Muhammad P. Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 6(2015) Page Start: 507 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
2. An experimental investigation of element diffusion and mechanical properties of solid WC/Co carbide tool in high-speed milling Ti6Al4V. (2015) Authors: Sun, Yujing; Sun, Jie; Li, Jianfeng Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 3/4(2015) Page Start: 319 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
3. Analysis of chip morphology in dry hard turning of AISI 52100 alloy steel using RSM. (2015) Authors: Khan, Zahid A.; Shihab, Suha K.; Siddiquee, Arshad Noor Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 6(2015) Page Start: 481 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
4. Application of a general regression neural network for predicting radial overcut in electrical discharge machining of AISI D2 tool steel. (2015) Authors: Pradhan, M.K.; Das, Raja Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 3/4(2015) Page Start: 355 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
5. Characterisation of abrasive tools active surface after the impregnation process by modified ARS method based on imaging and analysis of the scattered light. (2015) Authors: Kapłonek, Wojciech; Nadolny, Krzysztof; Wojtewicz, Michał; Sienicki, Walery Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 5(2015) Page Start: 397 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
6. Developing three dimensional transient thermal model for laser beam assisted heating and material removal of solids. (5th February 2015) Authors: Panda, Deepak Kumar; Raghav, Vivek; Bhoi, Rajat Kumar Journal: International journal of machining and machinability of materials Issue: Volume 16:Number 3/4(2014) Page Start: 259 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
7. Effect of reinforced particle size on wire EDM of MMCs. (2015) Authors: Pramanik, A.; Basak, A.K.; Islam, M.N. Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 2(2015) Page Start: 139 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
8. Electrochemical machining of 20MnCr5 alloy steel with ferric nitrate mixed aqueous NaCl electrolyte. (2015) Authors: Ayyappan, S.; Sivakumar, K.; Kalaimathi, M. Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 1(2015) Page Start: 79 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
9. Electrochemical micromachining for nanofabrication, MEMS and nanotechnology. (2015) Authors: Bhattacharyya, Bijoy Record Type: Book Extent: 1 online resource View Content: Available online (eLD content is only available in our Reading Rooms) ↗
10. Evaluation of neural models to estimate the roughness of advanced ceramics in surface grinding. (2015) Authors: Nakai, Mauricio Eiji; Júnior, Hildo Guillardi; Aguiar, Paulo R.; Bianchi, Eduardo Carlos; Silva, Paulo Sérgio Da Journal: International journal of machining and machinability of materials Issue: Volume 17:Number 5(2015) Page Start: 454 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗