1. An experimental investigation to the influence of traverse speed on microstructure and mechanical properties of friction stir welded AA2050-T84 Al-Cu-Li alloy plates. (2020) Authors: Kumar, Sanjeev; Sethi, Durjyodhan; Choudhury, Smrity; Saha Roy, Barnik; Saha, S.C. Journal: Materials today Issue: Volume 26:Part 2(2020) Page Start: 2062 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
2. Effect of in-situ processing parameters on microstructure and mechanical properties of TiC particulate reinforced Al–4.5Cu alloy MMC fabricated by stir-casting technique – Optimization using grey based differential evolution algorithm. (November 2016) Authors: Das, Biswajit; Roy, Susmita; Rai, R.N.; Saha, S.C.; Majumder, Priyanko Journal: Measurement Issue: Volume 93(2016) Page Start: 397 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
3. Effect of in-situ processing parameters on microstructure and mechanical properties of TiC particulate reinforced Al–4.5Cu alloy MMC fabricated by stir-casting technique – Optimization using grey based differential evolution algorithm. (November 2016) Authors: Das, Biswajit; Roy, Susmita; Rai, R.N.; Saha, S.C.; Majumder, Priyanko Journal: Measurement Issue: Volume 93(2016) Page Start: 397 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
4. Improved cooling capacity of a solar heat driven adsorption chiller. (February 2020) Authors: Rouf, R.A.; Jahan, N.; Alam, K.C.A.; Sultan, A.A.; Saha, B.B.; Saha, S.C. Journal: Case studies in thermal engineering Issue: Volume 17(2019) Page Start: Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
5. Investigation of correlation between chemical composition and properties of biodiesel using principal component analysis (PCA) and artificial neural network (ANN). (May 2021) Authors: Jahirul, M.I.; Rasul, M.G.; Brown, R.J.; Senadeera, W.; Hosen, M.A.; Haque, R.; Saha, S.C.; Mahlia, T.M.I. Journal: Renewable energy Issue: Volume 168(2021) Page Start: 632 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
6. Microstructure and mechanical property of friction stir welded Al-Mg joints by adopting modified joint configuration technique. (2020) Authors: kumar, Uday; Acharya, Uttam; Saha, S.C.; Saha Roy, Barnik Journal: Materials today Issue: Volume 26:Part 2(2020) Page Start: 2083 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
7. Modelling of Surface Roughness and Tool Consumption of WEDM and Optimization of Process Parameters Based on Fuzzy-PSO. (2018) Authors: Choudhuri, Bikash; Sen, Ruma; Kumar Ghosh, Subrata; Saha, S.C. Journal: Materials today Issue: Volume 5:Number 2(2018)Part 2 Page Start: 7505 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
8. Study of microstructure and mechanical properties in friction stir welded aluminum copper lap joint. (2021) Authors: Choudhury, Tapash; Ghorai, Arijit; Medhi, Tanmoy; Acharya, Uttam; Roy, Barnik Saha; Saha, S.C. Journal: Materials today Issue: Volume 46:Part 19(2021) Page Start: 9474 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
9. Study of surface integrity and recast surface machined by Wire electrical discharge machining. (2018) Authors: Choudhuri, Bikash; Sen, Ruma; Kumar Ghosh, Subrata; Saha, S.C. Journal: Materials today Issue: Volume 5:Number 2(2018)Part 2 Page Start: 7515 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
10. Study on machinability of in situ Al–4.5%Cu–TiC metal matrix composite-surface finish, cutting force prediction using ANN. (January 2016) Authors: Das, Biswajit; Roy, Susmita; Rai, R.N.; Saha, S.C. Journal: CIRP journal of manufacturing science and technology Issue: Volume 12(2016:Jan.) Page Start: 67 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗