1. Illustrative Multivariate Visualization for Geological Modelling. (10th July 2018) Authors: Rocha, A.; Mota, R. C. R.; Hamdi, H.; Alim, U. R.; Costa Sousa, M. Journal: Computer graphics forum Issue: Volume 37:Number 3(2018) Page Start: 465 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
2. A reconfigurable PID fault tolerant tracking controller design for LPV systems. (March 2020) Authors: Rabaoui, B.; Hamdi, H.; Braiek, N. BenHadj; Rodrigues, M. Journal: ISA transactions Issue: Volume 98(2020) Page Start: 173 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
3. Observer-based Fault Diagnosis for Time-Delay LPV Descriptor Systems. Issue 24 (2018) Authors: Hamdi, H.; Rodrigues, M.; Mechmeche, C.; Benhadj Braiek, N. Journal: IFAC-PapersOnLine Issue: Volume 51:Issue 24(2018) Page Start: 1179 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
4. A model reference tracking based on an active fault tolerant control for LPV systems. (25th March 2018) Authors: Rabaoui, B.; Rodrigues, M.; Hamdi, H.; BenHadj Braiek, N. Journal: International journal of adaptive control and signal processing Issue: Volume 32:Number 6(2018) Page Start: 839 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
5. Analytical and numerical study of the separation line between chip and work-piece during cutting processes. (1st January 2014) Authors: Salvatore, F.; Mabrouki, T.; Hamdi, H. Journal: International journal of machining and machinability of materials Issue: Volume 15:Number 1/2(2014) Page Start: 71 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
6. Improvement of the numerical modelling in orthogonal dry cutting of an AISI1045 steel by the introduction of a new friction model. (14th April 2011) Authors: Bonnet, C.; Rech, J.; Hamdi, H.; D'Eramo, E. Journal: International journal of machining and machinability of materials Issue: Volume 9:Number 3/4(2011) Page Start: 316 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
7. Residual stresses and metallurgic transformations induced by grinding. (14th April 2011) Authors: Youssef, S.; Salem, W. Ben; Brosse, A.; Hamdi, H. Journal: International journal of machining and machinability of materials Issue: Volume 9:Number 3/4(2011) Page Start: 223 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
8. Actuator fault estimation based adaptive polytopic observer for a class of LPV descriptor systems. (8th September 2014) Authors: Rodrigues, M.; Hamdi, H.; Theilliol, D.; Mechmeche, C.; BenHadj Braiek, N.; Casavola, Alessandro; Rodrigues, Mickael; Theilliol, Didier Journal: International journal of robust and nonlinear control Issue: Volume 25:Number 5(2015) Page Start: 673 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗
9. Numerical optimization of the Minimum Quantity Lubrication parameters by inner canalizations and cutting conditions for milling finishing process with Taguchi method. (1st December 2015) Authors: Duchosal, A.; Serra, R.; Leroy, R.; Hamdi, H. Journal: Journal of cleaner production Issue: Volume 108:Part A(2015) Page Start: 65 Record Type: Journal Article View Content: Available online (eLD content is only available in our Reading Rooms) ↗